Skip to content
Case care

How to take off a phone case without damaging the case or the phone

Free one top corner, then the other, and let the phone slide out. How that changes for hard snap-on shells, two-layer cases, clear cases and silicone.

Written by the YOONIG team · Updated · 7 min read

Hands peeling a printed phone case off the top corner of a phone

Start at a top corner and peel the case off the phone

To take off a phone case, hold the phone face down in one hand, hook a thumb under the case at a top corner and push that corner of the case back and away from the phone until the corner of the phone is free. Do the same at the other top corner, then slide the phone out of the bottom half. Never use the camera opening as a handle, and never pry with a tool.

The idea is the same for every case: the case moves, the phone stays still. Bending the phone out of a stiff case, or dragging it out by one edge, puts the force on the device and on the thinnest parts of the case.

The method, step by step

Do this over a bed, sofa or table. Phones are dropped more often while a case is coming off than at almost any other moment.

  • Unplug the cable and take off anything attached to the back: a magnetic wallet, grip or stand. If your case has a card slot, take the card out.
  • Turn the phone face down in your palm with the top edge pointing away from you.
  • Find a top corner. Put your thumb on the rim of the case at that corner, where the rim wraps onto the front of the phone.
  • Push the rim outward and back, away from the screen, while your fingers support the back of the phone. You are unhooking the rim from the front of the glass.
  • When that corner releases, move along the top edge to the second corner and release it the same way.
  • With the top free, lift the top of the phone a little and slide it up and out of the bottom of the case. Do not fold the case back on itself to hurry it.
  • Put the phone down on something clean before you deal with the case.

How each YOONIG build comes off

Our builds are made of different materials, so the amount of give differs. The descriptions here come from the maker's specification for each; which builds exist for your phone is shown on its device page, and all of them are compared in the case type guide.

Removing each case build: what it is made of and where to start
BuildWhat you are dealing withHow to take it off
SlimOne-piece rigid polycarbonate shell that snaps over the phoneUnhook one top corner with a thumb, then the other. The shell flexes very little, so go corner by corner; do not twist it.
ToughPolycarbonate outer shell over a TPU liner, raised edgesStart at a top corner as usual. If the soft liner stays on the phone, peel it off like a soft case and seat it back in the shell afterward.
MagSafe compatibleSame two layers with a magnetic module built inRemove any magnetic accessory first, then treat it as a Tough case. The magnets do not hold the case on; the rim does.
MagSafe + camera guardTPU frame with a polycarbonate back; the camera surround is part of the frameThe frame is the flexible part. Peel the frame off a top corner on the side away from the camera, then ease it past the camera area last.
Clear and Clear MagSafeClear polycarbonate back with soft TPU sidesThe sides bend, the back does not. Roll the soft side off a top corner; avoid bending the clear back.
Card holderSlim polycarbonate shell with a slot for one cardCard out first. Then remove it like a Slim shell, pressing on the rim and not on the slot.
SiliconeSolid silicone, covers around the lensesPeel a top corner back with a fingertip and roll the case down the phone. It stretches, so it needs the least force.

If the case will not budge

A hard shell that has been on for months can feel welded. It isn't; dust and skin oil have packed into the gap between rim and phone and added friction.

Change corners. One corner is usually looser than the others, and it is often the one next to the side with no buttons. Free whichever gives first and work around from there.

Use both thumbs on one corner, side by side on the rim, with the phone resting face down on a cushion. Push the rim away from the glass a few millimeters at a time and move along the edge between pushes. Short pushes along the rim work better than one big pull.

On a two-layer case, check whether the outer shell and the liner are coming off separately. If the shell slides off and leaves the liner on the phone, that is fine and often easier: take the shell off first, then peel the soft liner.

Do not reach for oil, soapy water or a hair dryer to loosen it. The maker's care notes for our printed cases say to keep them away from chemicals and excessive heat, and liquid run between case and phone ends up in the ports.

What damages the case, and what damages the phone

Almost all removal damage comes from four habits.

  • Levering against the camera. The camera opening is the weakest part of a rigid shell and sits beside the most exposed glass on the phone. Do not hook a finger through it or push the lenses to pop the phone out.
  • Prying with a tool. A coin, key or knife between case and phone marks the frame and chips the rim of a polycarbonate shell. Thumbs only.
  • Pulling at the button side first. The strip of case between the button openings and the rim is narrow. Start at a corner, where the material is widest.
  • Folding a hard shell backward. Polycarbonate is rigid by design; bend it far enough and it turns white at the fold or cracks. Soft TPU and silicone tolerate this, a printed shell does not.

When it is worth taking the case off

A case is not meant to stay on forever. The phone makers assume you remove it for a few routine jobs.

Cleaning is the main one. Apple's instructions for silicone and clear iPhone cases start with removing the iPhone from the case, then wiping the outside and the inside with a soft, slightly damp, lint-free cloth (Apple: How to clean your Apple products). Samsung likewise says to remove covers, cases and accessories before cleaning a Galaxy phone (Samsung: Keep your Galaxy phone clean). Grit that works its way inside a case can mark the back of the phone, so a look inside every couple of weeks is time well spent. The full routine is in how to clean a phone case.

Wireless charging trouble is another. Apple says that if an iPhone isn't charging or is charging slowly and it has a thick case, metal case or battery case, try removing the case (Apple: How to wirelessly charge your iPhone). Our Slim, Tough and Clear builds are listed by their maker as wireless charging compatible, so this is a test to rule the case out, not a routine.

Take it off as well when fitting a screen protector, when the phone has been in sand or got wet, and before any repair visit.

Putting it back on

Reverse the order: bottom first, top corners last. Check the inside of the case for grit and make sure both the phone and the case are fully dry.

For a one-piece case, seat the bottom edge of the phone into the bottom of the case so the port lines up, then press the top corners in one after the other until the rim snaps over the glass. For a two-layer case whose liner came out, fit the liner into the shell first, lining up the camera opening and button covers, and then fit the phone into the assembled case.

Run a finger around the rim. It should sit evenly on all four sides with no corner standing proud, the buttons should click, and the camera surround should be centered on the lenses. If a corner will not seat, the case may be for a different model; why phone cases only fit one model explains how small the differences can be.

A case that has gone loose, cracked at a corner or stopped gripping is due for retirement. The signs are listed in how often you should replace your phone case. Earbud covers come off differently, and that has its own page: putting on and removing an AirPods case cover.

Frequently asked questions

What is the easiest way to take off a phone case?

Hold the phone face down, push the rim of the case off one top corner with your thumb, free the second top corner, then slide the phone out of the bottom. Start at a corner, never at the buttons or the camera opening.

How do I remove a hard snap-on case that is stuck?

Try each corner to find the loosest one, then use both thumbs on the rim and push it away from the glass a little at a time, moving along the edge. Do not pry with a coin or knife.

Can taking a case off damage my phone?

Not if the case does the moving. Damage comes from prying with tools, pushing on the camera lenses or bending the phone out of a stiff shell.

Do I have to remove a two-layer case in two parts?

No. It usually comes off as one piece. If the soft inner liner stays on the phone, peel it off separately and seat it back inside the shell before you refit the case.

How often should I take my phone case off?

Every week or two to wipe out dust and grit, and any time the phone has been in sand or got wet. Apple's cleaning steps for cases begin with removing the phone.

Find a case made for your exact model

Shop the story

Keep reading